Hi-Intensity Single-Color Touring & Bagger Motorcycle LED Light Kit

$159.99
Install Resources
SKU: KMV-TOURING-SC
Current Stock:
SKU: KMV-TOURING-SC
UPC:
size: 8.00 W × 8.00 H × 8.00 L

Check out the Lighting Builder for a more customized experience.

Lighting Builder
Add to Wishlist

Hi-Intensity Single-Color Touring & Bagger Motorcycle LED Light Kit

Designed, Assembled and Supported In The USA

NEW CONFIGURATION! Now with 40% more LEDs!

Introducing our Hi-Intensity Single-Color Touring & Bagger LED Light Kit. Our most requested setup for baggers and touring bikes. This kit will light your bike from front to back. Built on our Hi-Intensity Motorsports LED strips, these strips have more LEDs per inch than comparable strips on the market today. More LEDs means more light shining on your bike! This kit uses a new and improved configuration of our Value and Premium Series LED strips with 40% more LEDs. Built with two ounce copper PCB, the brightest 5050 LEDs available and 1.2mm of genuine 3M® VHB double sided tape, these LED strips are made tough for motor sports applications. Impressively bright, our Hi-Intensity LED strips are thin so they can barely be seen when attached to the bottom of your tank or under your saddle bags. They produce a smooth, even glow of light. This Touring and Bagger kit lights your bike with the color of your choice. Original owner lifetime warranty on the LED strips. Many upgrade options too including Bluetooth wireless controller along with adding more lights.

LED LENGTH CONFIGURATION OPTIONS

Our Hi-Intensity Single-Color Touring & Bagger LED light kit is offered in two LED strip length configurations. We do this because some bikes have larger fuel tanks than others. The larger/longer fuel tanks have more room for LEDs on the bottom of them. Each configuration includes 8 Hi-Intensity LED surface mounted flexible strips in varying lengths plus two wheel lights. You'll typically want to choose the LED length configuration that has two LED strips that best fit the entire length of your fuel tank.

Configuration 1
2 - 18 LED strips. Each strip is 12.25" long (fuel tank)
1 - 18 LED strip. Strip is 12.25" long (ground effects)
2 - 6 LED strips. Each strip is 4.5" long (horn and breather)
1 - 12 LED strip. Strip is 8.38" long (battery box)
2 - 30 LED strips. Each strip is 20" long (saddlebags)
2 - Wheel Lights, each with 9 LEDs

Configuration 2
2 - 24 LED strips. Strip is 16.13" long (fuel tank)
2 - 3 LED strips. Each strip is 2.5" long (horn and breather)
1 - 18 LED strip. Strip is 12.25" long (ground effects)
1 - 6 LED strip. Strip is 4.5" long (battery box)
2 - 30 LED strips. Each strip is 20" long (saddlebags)
2 - Wheel Lights, each with 9 LEDs

*Each LED strip has a 36" power lead (22 gauge) hard wired to the end with the other end sealed. If necessary you can cut the LED strip every 3 LEDs. Just be sure to seal the end with liquid electrical tape or similar substance to keep from shorting out when wet.

Important Note On Purple LEDs! All purple LED’s on the market today are actually ultra-violet (U/V) and produce a soft purple glow particularly when used on motorcycle engines. The color however is not a real bright effect like you’ll get with red, blue, green, orange, etc. If you want a subtle purple glow that looks great, then the U/V LED’s may well be for you. If however you want the brightest lights possible, you will not be happy with purple.

Includes
Your choice of LED lengths from either of two configurations:
CONFIG 1) 3 - 18 LED strips, 2 - 6 LED strips, 1 - 12 LED strip, 2 - 30 LED strips.
CONFIG 2) 2 - 24 LED strips, 2 - 3 LED strips, 1 - 18 LED strip, 1 - 6 LED strip, 2 - 30 LED strips.
See LED lengths for each configuration in the product description.
Two (2) - 9-LED wheel light in your choice of case and LED color
Standard Front Wheel Wiring Kit
Complete wiring kit with push button on/off switch, in-line fuse and installation instructions. Everything you need to install all the lights in this kit
Original Owner LIFETIME Warranty on the LEDs and three (3) years on the controller
Options
Color Selection - Choose the color for your light strips and the color and case finish for your front wheel lights. If you have chrome calipers you will want a chrome case
Upgrade to our Front Wheel Wiring Kit with Steel Braid - if you have braided lines you will want to go with this option
Remote LED Controller - A wireless remote is NOT included with the base kit. You can add a wireless remote control if you'd like. See details of what's available in the CONTROLLER OPTIONS tab.

LED Controller & Remote Control Options

This kit includes a push button on/off switch. For added convenience, consider purchasing one of our wireless LED controllers to control your lighting. Here is a review of what's available for this kit:

  • Basic On/Off Controller - Simple on/off operation. Rated for 250 LEDs. KEY FOB control. SKU: KMV-TOURING-SC-OO
  • Single Color Multi-Function LED Controller w/KEY FOB RF Wireless Remote - On/Off with special effects include flashing, strobe, breathing and fading (dimming not available). Choose from our PLUS series rated to 300 LEDs or our SUPER Series that will cover you to 900 LEDs. KEY FOB control. SKUS: KMV-TOURING-SC-RF1-PLUS, KMV-TOURING-SC-RF1-SUPER
  • Bluetooth Smartphone LED Controller - Operate your lights using your Android or iOS smartphone. With the free app you can connect your single color lights to light your bike in sections or in it's entirety. Available in our SUPER series for up 900 LEDs. Note that this is a BLUETOOTH only controller. It requires you use your Bluetooth enabled smartphone to operate. SKU: KMV-TOURING-SC-BT-SUPER
  • COMBO RF + Bluetooth Multi-Function LED Controller - Operate your lights using the included RF wireless KEY FOB remote OR your Bluetooth enabled smartphone and our free APP. Features include ON/OFF, dimming, fading, strobing, flashing, breathing and the ability to save up to 3 presets. SKU: KMV-TOURING-SC-C1-PLUS

3 Zone Wireless Bluetooth Controller Options

  • SUPER Series Bluetooth 3 ZONE Smartphone Controller for Single Color Installations - This 3 Zone Bluetooth controller gives you an incredible amount of control over single color installations using your smartphone. Designed with creativity in mind, this Bluetooth controller allows you to isolate up the three zones of single color LEDs and then control each of those zones independently with your smartphone. Rated for 900 LEDs. The controller is a bit larger at 4-1/4" x 2-1/4" x 7/8" so make sure your installation has adequate mounting room. Note that this is a BLUETOOTH only controller. It requires you use your Bluetooth enabled smartphone to operate. SKU: KMV-TOURING-SC-BT-SUPER-3Z
  • HEAVY DUTY Series Bluetooth 3 ZONE Smartphone Controller for Single Color Installations - The same features as our SUPER, just more power! Rated for 2100 LEDs. This HEAVY DUTY controller is ideal for those single color installations where you have ample room for mounting and adequate power (10amps at least). This controller is the largest in our controller series measuring 5.5" long x 3.25" wide and 1.5" high. Note that the overall length to accomodate room for wires is 7.5" so make sure your installation has adequate mounting room. Note that this is a BLUETOOTH only controller. It requires you use your Bluetooth enabled smartphone to operate. SKU: KMV-TOURING-SC-BT-HD-3Z

Typical Installation

Each strip has a 36" power lead hard wired to one end of the strip. On a V-Twin the suggested layout for the lights is as follows:

  • Depending upon the LED configuration you purchased, install the 18 LED (or 15 LED) under the bottom of the tank on both sides. Install the 6 LED (or 3 LED) inside the horn cover and behind the breather backplate.
  • Depending upon the LED configuration you purchased, install the 6 LED (or 9 LED) behind the engine on the seatpan, oil/battery box or frame downtube. Align it to shine on the rear of the engine. Take the longer LED strip (15 or 12 LEDs depending the configuration you purchased) and install on the frame below the engine. Install on the inside of the frame so it won't be damaged by a jack or when loading onto a trailer.
  • Use the two 30 LEDs strips for rear saddlebag lighting. Measure your saddlebag support frames to see what will fit. If necessary, cut the strips and install on the bag frame support - not on the bag itself. Align slightly inward to light the pipes, rear wheel and ground. On some models that have a fender extension between the bag and fender you can cut one strip and install a segment on each extension. This blows the light down and toward the front of the bike. .
  • Install one MEGA stick on the inside of each front caliper. Run the power lead up the brake line and back to the power source. On bikes with a single caliper consider using the second wheel light on the rear wheel. Looks nice!

This kit is easy for a do-it-yourselfer. Includes all you need other than a few hand tools. Just like the chrome on your bike, this kit is fully expandable and allows you to easily add additional strips in the future.

These lights will also work well on a Can-Am Spyder. Order some extra strips until you get the coverage you want.

NOTE: We always recommend dry fitting or temporarily mounting the lights before installation to make sure you get the look you want. The suggestions above are our recommendations. The final mounting location for the lights comes down to your personal preference. So put them where it makes sense to you and for your bike.

Sealed, Flexible Strips

The LEDs on our HI-INTENSITY strips are sealed against the elements. They are heat resistant, waterproof and easily cleaned for a lifetime of maintenance free operation. The soft, gel-like strips provide maximum flexibility and a clean and sleek appearance. Their low profile design makes them virtually invisible when placed on the bottom of your tank and their wide viewing angle floods your bike with light.

Each strip has a 36" power lead which is hard wired to one end of the stip. If you need to cut a strip, be sure to cut where indicated on the strip (ever 3 LEDs) and make sure you seal the cut end with liquid electrical tape or something similiar to keep water from shorting out the strip. A wrong cut in the wrong place or not sealing the cut end properly will void your warranty. Call us if you are unsure where to make your cut.

Waterproof Black Quick Connector Options

The answer to future routine maintenance. Add these Waterproof Black Quick Connectors to your kit. Install inline on your tank wiring, breather, bags, side panels etc. Wherever future maintenance may require access.