FAQs

Installation Services

$95.00
Install Resources
SKU: PGU-INSTALL-WEEKDAY
Current Stock:
SKU: PGU-INSTALL-WEEKDAY
UPC:

Check out the Lighting Builder for a more customized experience.

Lighting Builder

Boogey Lights® Installation Services

We offer installation services for our LED light kits in our Florence, KY facility located at 9000 Empire Connector Drive Ste B, Florence KY 41042. Installation is by appointment only and in most cases, will require you to leave your vehicle for the day (sometimes longer).  We are typically booked at least 30 days out, sometimes further.  To schedule an installation appointment, select the Schedule Installation option on our CONTACT US page. We accept appointments Monday through Saturday. Our shop rate is $95 hour (Monday - Friday) plus shop supplies with a one hour minimum. Service time is billed in 15 minute increments thereafter. Saturday shop rate billed at a rate of $125/hour.  Sunday/Holiday shop rate  billed at a rate of $150/hour.

 

Helpful Links When Planning Your Installation with Boogey Lights

NOTE: If your vehicle doesn't have bathroom facilities on-board the City of Florence will not allow over-night stays at our facility.

 

 

Typical Installation Time Frames

Estimates only. 

RVs

  • Awning Light (not on slide-out): 1.5 - 3 hours
  • Awning Light (on slide-out): 2 - 4 hours
  • Awning Light integration with existing On/Off factory switch:  1 hour per switch connection
  • Top of Slide-Out: 2 - 4 hours
  • Under Slide-Out: 2 - 4 hours
  • Standard Under-Glow: 3-4 hours
  • Under-Glow Add-On: 1 additional hour per Add-on
  • Motor Homes: If your house batteries are located behind the drive axle on the driver's side, add 1.5 - 3 hours. If on the passenger's side behind the drive axle, add 1-1.5 hours.
  • Rock-Guard Light Kit w/UG + TTB: 4-6 hours
  • Rock-Guard Light Kit w/UG: 2-3 hours
  • Rock-Guard Light Kit w/TTB: 3-4 hours
  • Engine Light Kit integration with UG:  2 hours
  • LED End Cap Replacement:  2-3 hours for single color.  5 - 6 hours for multi-color.  Note: Multi-color requires the cutting of at least one access panel (typically 8"x8") on the inside wall facing the end cap.  

Note: In almost all cases, it will be necessary to drill into the RV; this is particularly true for awning light kits and/or lights attached to slide-outs. It's unavoidable for a professional installation. We of course make every effort to minimize the number of holes and seal all holes with Lexel and/or Butyl tape. We will discuss the installation process with you once we are able to inspect the RV in person.

Semi-Truck

  • Under-Cab w/Controller: 4 - 6 hours
  • Grill Light: 2 - 3 hours
  • Under- Front Bumper: 2 - 2.5 hours
  • Hood Air Vent Lights: 2 - 2.5 hours
  • Rear Fairing Lights: 4 - 6 hours 
  • Add Tail/Turn/Brake integration to rear fairing lights: Add 3-4 hours 
  • Under-Glow (frame rails): 3 - 5 hours
  • Add-On Strips: .5 - 1 hour per strip depending upon placement location and wiring.

Motorcycle

  • Sport Bike: 6-8 hours
  • Touring & Bagger: 6-12 hours depending on the bike
  • Gold Wing: 8-14 hours depending on the bike
  • Trike: 6-12 hours depending on the bike
  • Add-On Strips: .5 - 1 hour per strip

    Note: The above hours estimate are for standard LED accent light kit installs (e.g. engine lights, horn, breather, under-glow, brake calipers, under bags). If additional lighting is requested, there will be additional time required. Also, there are some areas we typically will avoid lighting including the inside of speakers and in areas where there is factory-installed fairing lighting.  These areas are difficult to get to without significant tear down and often can only be lit using custom designed lights and/or mounting brackets.   If the project requires removal of existing LED lighting, there will be additional time required.

ATV | SXS | Golf Cart

  • Under-Glow w/controller: 2-3 hours
  • Add-On Strips: .5 - 1 hour per strip
  • Add grill light: 1 - 1.5 hours
  • Add cab/internal/roof light: 1 - 1.5 hours

Cars / Pickup Trucks

  • Under-Glow (base kit w/2 strips) w/controller: 3-4 hours
  • Front + Rear Add-On Under-Glow: 2 hours (1 hour per)
  • Grill Lighting: 2-5 hours depending upon complexity of the grill removal process.
  • Hellcat Grille Light Kit: 5 hours.  Add 1 hour for Hood Scoop/Vent lights.
  • Wheel well lights: .5-1 hour per wheel

Marine

  • Base 2 strip light kit w/controller: 3-4 hours
  • Add-On Strips: .5 - 1 hour per strip

Food Trucks/Trailers, Utility/Horse/Cargo Trailers

  • Awning or LED Light strip mounted to the side of the trailer (not on slide-out): 1.5 - 3 hours
  • Under-Glow: 2 - 4 hours
  • Add-On Strips: .5 - 1 hour per strip depending upon placement and power connection

 

Time frames are estimates. We will provide a not to exceed number once we know specifically which kit(s) you want installed and have a chance to review the vehicle. All installation work is warranted for one year at our facility in Florence, KY.   Note:  An installation schedule deposit may be required at the time the installation appointment is booked.

 

Schedule Installation