Install Docs

C7 Corvette LED Under Glow Light Kit

Price as Configured
UPC: 812928020004
Current Stock:
UPC: 812928020004
size: 10.00 W × 10.00 H × 6.00 L
Price as Configured
Prices for product only. Installation not included.
A Word about Delivery Time Frames

C7 Corvette LED Under-Glow Light Kit

With Grill, Hood Scoop and Wheel Vent Add-On options.

Light up your Vette with 300 super bright hi-intensity LEDs!

Designed specifically for use in motor vehicle applications, this multi-color RGB LED light kit is incredibly bright - no other competitor comes close. Designed for the C7 Corvette Stingray, Grand Sport and Z06 (2014-2019) our low profile hi-intensity LED strips produce a smooth, even glow of super bright light to give your C7 that custom look. Unlike all the others, this BOOGEY LIGHTS Corvette C7 Under-Glow light kit contains 300 super brights LEDs -- at least twice the number of LEDs of any competitor. Plus, we only use 5050 LEDs -- the largest, brightest 12vdc LEDs available.


With this many LEDs you get true, FULL PERIMETER lighting under the car. Also includes lights to illuminate the exhaust tips. PLUS, if you want to add more lights, we offer optional ADD-ON LED light kits too including kits to light up the C7's grill, hood scoop, front and rear fender cove vents.  Note: Above photos show the under-glow, vent cove, grill and hood scoop LED light kits installed. 

Control this light kit using either the included RF hand held RF wireless remote OR your Bluetooth enabled smartphone and our free APP (IOS / Android).

With the RF hand held remote and the Boogey Lights RGB LED controller you can change between seven pre-set colors: white, red, green, blue, pink, lime green, light blue. Also, you can control the functions of on/off, color blending, strobing, breathing, flashing, fading and 7 levels of dimming. In the Blending, Breathing, Flashing and Strobing modes these features can be set to remain on a single color or to cycle through each of the 7 colors. You can also adjust the speed at which this happens.

With our Bluetooth APP and your smartphone, you can do everything the RF hand held remotes does PLUS you can create a custom look with over 16 million possible different color combinations plus three pre-sets along with two or three color programming functionality. Click on the GEN2 LED Controller text block for details.


This led light kit is available in the following five configurations:

  • Under-Glow Only
  • Under-Glow + Grill
  • Under-Glow + Grill + Hood Scoop
  • Under-Glow + Grill + Vents (4: 2 forward, 2 rear)
  • Under-Glow + Grill + Hood Scoop + Vents

Make your selection from the drop down box.

Note: The installation video shows three small LED strips (each with 3 LEDs) installed in the crease of the hood scoop. This kit doesn't include those three small strips but it's something you could add if you want. Ask use about it and we'll direct you to the product we used.

GEN2 LED Controller

Our GEN2 LED Controllers are based on the Bluetooth 5 chip set family which provide fast response times and the best possible RF/Bluetooth transmission distance. This controller is designed to be used with RGB/Multi-Color LEDs although it can also be used with single color LEDs too. In addition to ON/OFF, this controller provides DIMMING, STROBBING and FLASHING capabilities. Plus, this LED controller will work with your Android® or iOS® Smart phone equipped with Bluetooth (max of 16 million color possibilities). With the included RF remote you can change between 7 colors (Red, Green, Blue, White, Light Blue, Lime Green/Yellow, Hot Pink/Purple) and functions of on/off, blending, strobing, breathing, flashing, fading and dimming. You can also use your Bluetooth enabled smart phone to create that custom look with over 16 million different color combinations plus three pre-sets and color rotation programming. It will also work with the included RF wireless remote. You get the best of both worlds. More details about these advanced GEN2 LED Controllers are below as well as on the CONTROLLERS navigation tab of this product page.

Single Zone or Dual Zone?

We offer the option of a single zone (default) or dual zone (upgrade) LED controller. With the single zone controller all of the LEDs will do the same thing. They turn on and off together. With the optional Dual Zone LED controller, you can segment the LED lights into two separate light zones. For example, you may want to wire the Under-Glow and Grill on ZONE ONE and the Hood Scoop and Vents on ZONE TWO. This will allow you to control each of the zones independently. It's handy for situations where you might want to turn off the Under-Glow/Grill but turn on the Hood Scoop and Vents. Or, you might want to set zone one LEDs on one color and zone two LEDs on another. Lots of flexibility with the DUAL ZONE controller.

  • DOWNLOAD the GEN2 LED Controller Operating Manual & Wiring Diagrams
  • DOWNLOAD the GEN2 Bluetooth Operating Manual
  • DOWNLOAD the GEN2 M7 RF Wireless Remote Operating Information
  • VIEW the GEN2 LED Controller Series Product Page
  • VIEW the GEN2 BLUETOOTH APP Information Page
More About the GEN 2 Boogey Lights® Bluetooth Smartphone APP


Here's a 7 minute video showing the installation of this light kit. The INSTALL navigation tab of this product page has the details of the LED strip placement along with photos of the installation.



No two installation scenarios are the same. Not everyone shares the same installation quality goals. Some folks are OK with twisting wires together, others want to solder them. Some folks are OK with running wires where they may be seen or unprotected to save money/time, others want a tidy, clean install without any wires showing. Some folks are OK with mounting their LED strips to whatever surface they can find, others want to take the time necessary to build out appropriate mounting surfaces to provide the best lighting effect on their vehicle. The point is it's not possible to provide all the materials necessary for all installation scenarios and quality goals. Our light kits provide the essential components needed for a high-quality, functioning lighting system. Installation of our light kit to your specific vehicle may however require additional items to make it look and fit the way you want. This is particularly the case with electrical wiring and mounting of LED strips. Before proceeding with your installation we suggest you consider THESE OTHER ITEMS.


The short answer is probably not. All Boogey Lights® RGB LED strips are COMMON CATHODE LEDS. They share a common ground and will only work with positively switched controllers. Most LED strips on the market today are COMMON ANODE because the controller technology used to power them is less expensive to manufacture. However they're not nearly as bright and are an overall inferior design when compared with COMMON CATHODE LEDs. For more information, click the button below.

Will Boogey Lights® Components Work with Other Brands?


Unlike most every other light kit out there, these light kits are ACCENT LIGHT KITS. When mounted properly, you'll never see the LED lights themselves. You'll only see the glow from the LEDs. If you're interested in learning more about WHY Boogey Lights are different than any other LED lighting system on the market, click here: WHY BOOGEY LIGHTS . We do a deep dive into the ten differences between Boogey Lights® and all the others.


Five LED strips containing a total of 300 super bright, hi-intensity 5050 LEDs. Each strip includes a hardwired power lead. LEDs are mounted on black PCB made of 2 ounce copper with a clear coating to protect the LEDs. The strips are IP65 rated; designed to be used outdoors. LED strip width is 3/8" (10mm). Height is 1/8" (3mm). The power lead is soldered and sealed at one end. 4-conductor power lead (red, green, blue and black) for RGB multi-color. See installation tab for layout.
1 - Single Zone GEN2 Wireless RF + BLUETOOTH COMBO RGB LED controller with RF wireless remote control. This controller will power up to 900 LEDs. Optional upgrade to a DUAL ZONE LED controller.
OPTIONAL LED LIGHT KIT Upgrades include: Grill Light Kit, Hood Scoop Light Kit, Front/Rear Fender Cove Light Kit
Installation Supplies
Installation Manual and Wiring Diagram
One Year Original Owner Warranty
Return Policy Exception Notice. This kit subject to a 35% restocking fee due to the amount of time associated with producing this kit, shipping costs and the custom nature. See return policy for complete details.

Installation Information

You can DOWNLOAD OUR INSTALLATION GUIDE for this product directly from our website. It's a PDF file.

The layout for each light kit configuration is as follows:


  • 2 - 65" (99 leds each) low profile LED strips. One mounted on each side of the car.
  • 1 - 31" (48 LEDs) low profile LED strip mounted under the front bumper.
  • 1 - 13.75" (21 LEDs) low profile LED strip mounted above the exhaust on the rear.
  • 1 - 22" (30 LEDs) heavy duty LED strip mounted under the rear bumper.


  • 1 - 17.75" (27 LEDs) low profile LED strip mounted in the grill.

In our experience, the front bumper has to be removed to give you enough room to install this LED light strip in a location that illuminates the grill area without being able to see the LED directly. We know some guys have done it without removing the front bumper due to the time involved but it doesn't look nearly as good in our view.


  • 1 - 17.75" (27 LEDs) low profile LED strips mounted at the top of the hood scoop
  • 2 - 6" (9 LEDs) low profile LED strips mounted on each side of the inside of the hood scoop.

Note that the hood scoop kit includes a quick disconnect M/F connector that needs to be installed between the hood scoop assembly (where the 3 LED strips are mounted) and the power lead connection coming from the car. This allows the hood scoop assembly to be removed for service without having to cut any wires. Yes, you have to remove the hood scoop to install these lights. The installation video shows three small LED strips (each with 3 LEDs) installed in the crease of the hood scoop. This kit doesn't include those LEDs but it's something you could add if you want.


  • 2 - 13.75" (21 LEDs) low profile LED strips mounted inside the front vents
  • 2 - 11.75" (18 LEDs) low profile LED strips mounted inside the rear vents

Photos of the placement of these LED strips are below. We also include an installation video. The placement doesn't have to match exactly. Adding accent lighting to your vehicle is all about achieving the look YOU want. As long as the LED strips are mounted to a location that is smooth, flat, straight and doesn't span multiple surfaces, it's ultimately up to you to decide what look you like the most. When installed properly, you shouldn't be able to see the LED strips themselves – only the glow from them.



Boogey Lights LEDs Lights
Boogey Lights LEDs Lights
Boogey Lights LEDs Lights
Boogey Lights LEDs Lights
Boogey Lights LEDs Lights
Boogey Lights LEDs Lights
Boogey Lights LEDs Lights
Boogey Lights LEDs Lights
Boogey Lights LEDs Lights