ADD-ON RGBWW LEDs with Power Lead
MULTI-COLOR RGBWW LED ADD-ON Strips with Power Leads
Now you can have WARM WHITE, NATURAL WHITE and BRIGHT WHITE on a Multi-Color RGB LED Strip!
Hi-Intensity Multi-Color RGBWW LED ADD-ON strip with heat shrink power lead and mounting supplies. Your choice of varying lengths of LEDs and power lead to suit your application. Low-profile, 5050 super-bright high-intensity RGBWW LEDs, IP65 rated, 1.2mm 3M backing tape for extra holding power. 12vdc. Adhesion primer is NOT included so be sure to order some 3M Adhesion primer tubes or cans.
- Power leads use 22AWG six conductor wire. The power lead connection to the LED strip hard-wired and sealed to the strip.
- LED strip width is .47" (12mm). LED strip height is 1/8" (3mm).
Please allow one extra day for shipping. Due to the custom nature of our ADD-ON LED strips we do not stock every possible combination of LED lengths and power lead lengths. Some of the less popular combinations have to be made as the order comes in.
NOTE: All Boogey Lights® LED strips are COMMON CATHODE LEDS. They share a common ground and will only work with positively switched controllers. Most LED strips on the market today are COMMON ANODE because the controller technology used to power them is less expensive to manufacture. However they're not nearly as bright and are an overall inferior design when compared with COMMON CATHODE LEDs.
NOTE ON EXTENDED USE: The LEDs used in this product are very bright; the brightest 12vdc LED lights available. They're designed to be used for accent lighting applications where they are typically powered on for a few hours (usually on a dimmed setting) and then powered off. While they can be used in functional lighting applications (e.g. bright white to temporarily illuminate a work area), the lights should NOT be left powered on for extended periods of time (e.g. 6+ hours). If the LEDs are left powered on for long periods of time - particularly on their brightest setting - the LEDs closest to the power source will have a burned look to them over time. This is because the amount of voltage being pulled through the LEDs closest to the power source will be higher than the voltage going through the LEDs further down the strip. The end result is that those LEDs closest to the power source will be hotter thus creating the burned look. This will occur mostly when displaying the color white on a full brightness setting but can also occur with other colors. For this reason, we do NOT suggest leaving these LED lights powered up for extended periods of time particularly on their brightest setting. Burned looking LEDs is NOT covered under warranty.
IMPORTANT WARRANTY INFORMATION
Boogey Lights Low Profile Hi-Intensity Surface Mounted LED light strips are used in a number of Boogey Lights products for a variety of vehicle applications (including this product). Where and how these light strips are installed make all the difference in their durability and thus, our warranty. For this reason the duration of the Boogey Lights Low Profile Hi-Intensity LED Light Strips original owner warranty varies based on the vehicle application, use and installation types.
- Recreational Applications: RVs, Motorcycles, Golf Carts: 3 years
- Cars/Pickup Trucks/Off-Road: 1 year
- Marine / Fresh Water: 3 years
- Marine / Salt Water: 90 days
- Food/Cargo Truck/Trailer, Other Light Duty Commercial Use / Installation done by Boogey Lights technicians in Florence, KY: 3 years
- Food/Cargo Truck/Trailer, Other Light Duty Commercial Use / All other installation types: 1 year
- Heavy Duty Truck and/or Trailer Commercial Use / Installation by Boogey Lights technicians in Florence, KY: 1 year
- Heavy Duty Truck and/or Trailer Commercial Use / All other installation types: 90 days
Note on Commercial Applications: These low-profile surface mounted LED strips are not built to withstand significant flexing or lateral movement of the surface the strip is mounted to. Some examples include on semi-truck trailers as well as tow trucks where there is significant movement, bending or flexing of the surface to which the strip is mounted. Also, the strip can not mounted in such a way as they span multiple mounting surfaces. Mounting them this way will virtually guarantee the strip will fail sooner rather than later. These strips must be mounted to one single continuous smooth, clean, flat surface and in an area that is protected from corrosive chemicals. Commercial vehicles that frequently travel roads treated with corrosive chemicals often used for melting snow and ice can impact the durability of these LED strips if the strips are mounted in an area that is exposed to these chemicals. Hi-Intensity Strips that fail in these operating environments ARE NOT COVERED UNDER WARRANTY. For these types of operating environments we strongly recommend (and warranty) our HEAVY DUTY LED strips.
View the complete limited product Warranty Terms & Conditions here.
Designing Your Lighting Solution
There is no set installation configuration. Whether you have a motor home, bus, 5th wheel, tag-along travel trailer, pontoon boat, utility trailer, food truck or semi-truck the configuration concepts are pretty much the same. Your rig and your imagination are the only limits (well, and your budget). Here are some things to keep in mind when designing and installing our Hi-Intensity LED Strips.
- Our Hi-Intensity LED strips can be cut every 3 LEDs to accommodate shorter runs. Just make sure you are cutting them where marked AND that you seal the cut end to keep moisture out.
- The maximum length of one Boogey Lights® Hi-Intensity strip is 16'. Multiple 16' strips CAN NOT be daisy chained together. If you want to do a run longer than 16', you can butt two strips together to get the desired length. That said, we rarely see an installation that required doing this for a lack of light. Boogey Lights® LEDs are so bright that one 16' strip should provide more light than you'll need. Simply centering one 16' strip will in most cases be sufficient.
- If you're using our multi-color LED strips, the maximum number of 16' LED strips that can be powered at one time depends on which controller you're using. Our Heavy Duty controller will power at least six 16' LED strips. You might be able to get 7 depending upon your wiring. That said, it's possible to add additional controllers and manage those controllers with one RF remote. Lots of possibilities. The limitation ultimately comes down to your power source.
- If you're using our single-color LED strips, make sure you are not over-loading the circuit they are attached to. As with all lighting solutions, each LED strip should be properly fused. If for any reason there is a dead short in the strip, you want the power to that strip to be cut off to avoid over-heating and potentially burning.
- For multi-color LED strip installations, be mindful of where your power source is located as well as where you will be mounting the controller. The power lead for each Hi-Intensity strip needs to connect directly to the controller at your power source. Knowing where your controller will be mounted in relation to where the LED strip will be placed will determine how much power lead cable is needed on each LED strip.
- When mounting on the bottom of any vehicle we recommend making sure you are not mounting the strip in-line with the wheels or in areas that might be prone to a direct strike from road debris. While Boogey Lights® Hi-Intensity LED strips are made for motorsports applications, they will likely not survive a direct strike from a hard object. If you are concerned the LED strips might be hit by road debris due to their mounting location we recommend using our Heavy Duty LED Strips which are better able to survive a direct strike from road debris.
- The only way to ensure the LED light strip stays stuck to is to make sure you prepare the surface in accordance with the directions. This includes making sure the mounting surface is smooth and free from oil, wax or other solvents. Most LED light kits we sell includes 3M® promoter (aka "primer"). It's absolutely critical the surface be prepared using this 3M® promoter and that you follow the directions provided with every light kit. For the power lead wires that feed the LED strip we include some extra 3M® tape and zip tie mounts. If you purchased an LED light strip that does not include this primer, we offer primer for sale individually or in cans.
- The length of power lead between the LED light strip and the power source absolutely impacts the brightness and power consumption of the light strip. This is an important concept to keep in mind when designing your setup. For power lead lengths longer than 15 feet (and less than 76'), we recommend using 20 gauge power lead wire which we offer for sale on our website. The lower the gauge number, the thicker the cable. The thicker the cable, the less power loss there is over longer distances.
- AMPERAGE Data for most Boogey Lights products can be found on our website.
- When in doubt, call our technical support team! We're the experts. We've done this thousands of times. We know what works.