Low Profile LED Light Strips

All BOOGEY LIGHTS® Low Profile LED strips are impressively bright (except UV/Purple - see note below). Built with two ounce copper PCB, the brightest 5050 LEDs available and 1.2mm of genuine 3M® VHB double sided tape, these LED strips are made tough for use outdoors on vehicles and other motor sports applications. The LEDs are completely sealed against the elements. They're IP65 rated. They are heat resistant, waterproof and easily cleaned for maintenance free operation. The soft, gel-like strips provide maximum flexibility and a clean and sleek appearance. Their low profile design makes them easy to fit into tight spaces and yet are incredibly bright; nothing brighter on the market.

They're available on either white or black PCB in varying lengths ranging from 3 (2") to 300 LEDs (16'). The default configuration has one 36" power lead hard wired to the end of the strip with the option of adding a second power lead on the other end of the strip for motorcycle applications. Note that this option is only available for Motorcycle lighting applications because they typically will use a larger number of very short LED strips where the total number of LEDs is under 300.  It can be handy if you don't know the exact length of LED strip you need but you don't want any waste. Simply cut the LED strip in the appropriate location and you now have two strips each with their own power lead. The LED strips can be cut every 3 LEDs. See details on how to cut our LOW PROFILE LED strips here. If you want longer power leads, we offer additional power lead length options. If you are going to "daisy chain" LED strips together, make sure you do not exceed the maximum of 300 LEDs in a single run. This is super important as you not only void our warranty by doing so but you run the very real risk of starting a fire.

Power Lead Length Options: This product is offered in your choice of Power Lead Lengths in increments of 36" (default), 5', 10', 15' and 20'. Power lead wire gauge is 22awg. The power lead wire outer jacket is GREY for Black PCB and WHITE for White PCB. If you need to go longer than 20', we offer additional POWER LEAD WIRE to extend as needed. NOTE: There are NO CONNECTORS. Each power lead has bare wire on the other end (2, 4, 5 or 6 conductors depending on the product). All connections are hard wired. This is by design.

Our Low Profile LED strips are dimmable when used either with a Boogey Lights® LED controller or wired LED compatible dimmer switch.

NOTE: DOT issues notwithstanding, our Low Profile LED light strips should not be mounted on motor vehicles running at highway speeds facing forward unless they are mounted inside of an enclosure or have some other protective shield in front of them.

If you intend on mounting the LED strip in plain view or an area of your vehicle that will allow the LED strip to be easily hit or damaged in some way (e.g. mounting on running boards, service truck body side, etc), we strongly suggest mounting the LED strip using Aluminum Channel with Opaque Plastic Diffuser. Scroll down on this product page for details on this mounting solution.

Boogey Lights® RGB, RGBW, RGBA and RGBWW LEDs are common cathode LEDs. They share a common ground and will only work with positively switched LED controllers. Most third party led controllers are negatively switched controllers and will not work with Boogey Lights RGB, RGBW, RGBA or RGBWW LEDs. If you order any of the RGB LED strips listed here you will need a positively switched LED controller to operate.  That LED controller is not included. It has to be purchased separately.  We offer a wide selection of LED CONTROLLERs here.

RETURN POLICY EXCEPTION. This product is considered to be a custom product. We build these LED strips to the lengths/colors you specify in the order. It is not eligible to be returned for a refund. STORE CREDIT only. Be sure to read our RETURN POLICY for details.

The maximum length of a single LED strip is 16' (300 LEDs). They cannot be daisy chained together as you run a very real risk of fire and/or damaging the LED strips permanently. The laws of electricity won't allow it to go longer with today's commercially available technology using 12vdc power and super bright 5050 led chips. If your application requires longer than 16' (e.g. 20'), you have two options. One is to simply center the 16' LED strip in that 20' space. Boogey Lights are already very bright so for most folks, having enough light is never a concern. This is what most people do. That said, some prefer to have full coverage of the entire 20' area. In that case it's possible to cover that entire 20' span using two LED strips. In the case of a 20' span you can order two - 10' LED strips. Then, the two LED strips (totaling 20') are installed such that the two LED strips butt together; end to end, which gives the illusion of a single 20' long LED strip.

The RGB, RGBW, RGBA and RGBWW multi-color strips requires an LED controller to operate the RGB diodes.

If you're purchasing the LOW PROFILE LED Strip and you intend on mounting the LED strip in plain view or an area of your vehicle that will allow the LED strip to be easily hit or damaged in some way (e.g. mounting on running boards, service truck body side, etc), we strongly suggest mounting the LED strip inside this ALUMINUM CHANNEL with PLASTIC DIFFUSER on top. Why? Because they protect the LED strip from a direct strike AND provide a professional looking installation. Not only does the aluminum channel and diffuser protect the LED strip the opaque plastic diffuser gives off a nice glow lighting effect too. The Mini T12 Aluminum Channel is a low profile design that can be mounted just about anywhere. It has an anodized finish (electrostatic sprayed) which provides maximum protection against the elements. They're ideal for harsh indoor or outdoor use to protect the LEDs. The channel can be mounted any number of ways including adhesive tape, rivets or screws. We typically rivet the channel to the surface where possible. Then, the LOW PROFILE LED strips fit nicely into the channel using the 3M tape already affixed to the back of Boogey Lights LED rolls. The diffuser completes the installation by snapping into the channel. On outdoor installations we advise adding some lexel / silicone to the ends of the channel to seal it.

RGB stands for RED, GREEN, BLUE. Each LED chip on the strip contiains three diodes: One Red. One Green. One Blue. When paired with an LED controller, the mixing of those three primary colors can create up to 16 million different color combinations. For example, equal parts RED + GREEN + BLUE = WHITE (bright white, 6000 Kelvin temp). RGB leds are the most common leds due to their versatility in creating so many different color combinations.

Single Color LEDs will always be brighter than multi-color. If you're looking for the absolute brightest LED, Single Color is what you want. Why? All of our RGB and Single Color LEDs use a 5050 tri-chip LED. Each 5050 LED has three LED diodes. In a RGB LED those three diodes are red, green and blue. When combined with an LED controller the mixing of those three colors will produce up to 16 million different color combinations. For example, using an RGB LED chip mixing equal parts red + green + blue will produce WHITE (6000 Kelvin temp.) In a single color tri-chip LED there are also three LED diodes however all three of those LEDs are the same color. Because there are three diodes of all the same color, the light will be brigther. Of course you only get one color with a Single Color LED so there are trade offs. Important to note that 5050 LED chips are the brightest available. So even an RGB LED Chip will produce a very bright light. In fact, most people find they need to dim them. We rarely have a customer tell us the lights are not bright enough. And in the cases where they do, it's because they don't have sufficient power to support the amperage load (and the lights dim).

For Single Color LEDs, we offer the ability to order the strip with either a 2 conductor or 4 conductor power lead wire. The default is 2 conductor (black and red). Each LED has 3 diodes. In a single color LED, all 3 diodes are the same color. We normally will bridge the 12vdc power at the end of the strip such that all 3 diodes are connected to the red power lead conductor. If however you want to be able to control the power going to each of the 3 diodes, we will use 4 conductor power lead cable. This configuration is ideal for situations where you're using the single color LED strip and want to control the brightness of the strip by lighting one, two or all three diodes (e.g. brake lights, turning indicators and running lights.)  

Color temperature is a method of describing the color characteristics - warmth or coolness - of a white light source. Commonly referred to as the Correlated Color Temperature (CCT), it's a gauge of how yellow or blue a white light source appears to the human eye. The spectrum of color temperature is assigned a numerical value, measured in degrees of Kelvin (K), on a scale of 1,000 to 10,000. Most Kelvin temperatures for modern lighting applications however fall somewhere on a scale of 2000K to 6500K. The color temperature of a light source lets us know what the look and feel of the light produced will be.

We offer three different Kelvin temperatures of WHITE as follows: COOL WHITE (6000K), SOFT WHITE (2400K) and NATURAL WHITE (4000K).

Cool White (aka Bright White) is the most popular and is by default what we ship the most. It's also the color of white that is created with RGB LEDs (mixing equal parts red + green + blue = cool white). It's excellent for functional lighting and is used the world over in offices, public places, warehouses and the like.

Soft White (aka Warm White or Candle White) is the second most popular since it provides a nice contrast to the Cool White. It's on the opposite end of the Kelvin scale with a 2400K temp. Soft White has a yellowish tint to it making it softer; easier on the eyes - not nearly as bright as Cool White though. It's great for creating ambiance but not functional lighting. You'll notice we offer an RGBW product that includes RGB + one diode of this soft white color which provides both Cool White and Soft White options (along with RGB of course). It's our most popular Multi-Color LED strip for this reason.

Lastly, we offer a Natural White (aka Neutral White) which has a Kelvin temp of 4000. This shade of white is middle of the road - half way between Soft White and Cool White. We offer it in a single color only. See below images to help demonstrate the differences.

On the RGBW led strip, in addition to RGB, you get one extra diode which is Warm White. That warm white diode has a Kelvin temperature of 2400 which means it has a yellowish look giving it a warmer, softer, candle like look (see photo below). That fourth diode on the RGBW led strip can be wired directly to our GEN2 LED Controller which supports RGBx LEDs. As an option, you could also wire that fourth diode to a completely separate on/off switch. Your choice. You could also use the Quick-Switch feature with this fourth diode too.

An RGBWW LED chip contains five light emitting diodes: 1 red, 1 green, 1 blue, 1 warm white and 1 natural white. It's the addition of these two variations of white diodes that makes the difference. The RGBWW LED chip will not only produce all of the same colors as the standard 3 diode RGB LED chip, it can also produce warm white, natural white and cool white.

NOTE: This product has been discontinued. Once we sell through the existing RGBWW components, we will no longer offer RGBWW. The reason is the vast majority of customers can use RGBW to achieve the lighting effect they're looking for. RGBW is easier to work with, more durable and less expensive than RGBWW.

RGBA is a new type of LED strip we designed. It includes our core RGB tri-chip technology with the addition of a fourth diode that is AMBER. Designed primarily for motor vehicle applications, that fourth AMBER diode can be wired to a separate switch on the dash that allows you to quickly and easily turn on just the AMBER leds which meets DOT compliance regulations. Then, for those who want the flexibility to also be able to display up to 16 million other color combinations using our RGB LED Controller, they can do that too. RGB + A provides the best of both worlds. Note that due to the addition of that fourth diode, the RGBA LED strip is wider than our standard tri-chip LED strips.  They're 11/16" wide (vs 1/2" for the tri-chip strips). For additional information including product specs, click the SPECS navigation tab on this product page.

REDA is a new type of LED strip we designed. It uses our single color RED tri-chip technology with the addition of a fourth diode that is AMBER. Designed primarily for motor vehicle tail-turn-brake applications, that fourth AMBER diode can be wired to the left and right turning indicator circuits. The remaining three RED diodes are wired such that one diode connects to the running light circuit and the remaining two diodes connects to the brake circuit.

REDW is a new type of LED strip we designed. It uses our single color RED tri-chip technology with the addition of a fourth diode that is WHITE (6500 Kelvin). Designed primarily for motor vehicle tail-turn-brake applications, that fourth WHITE diode can be wired to the reverse light signal. The remaining three RED diodes are wired such that one diode connects to the running light circuit, one to the brake circuit and one to the turn signal. Another option is for emergency, wrecker or recovery vehicles that need to flash red and white. In this scenario the REDW LED strip is often paired with our Single Color Strobbing / Flashing LED Controller.

The Dual Color LED configuration uses our RGBA LED strip but instead of pairing that LED strip with an RGB LED controller (to mix up to 16 million different color combinations), we hard wire a combination of one, two or all three of the RGB diodes (red, green or blue) along with the AMBER diode to two on/off switches. One switch operates the primary color diode(s). The other switch operates the amber diode. There are a total of seven Dual Color configuration options: RED+AMBER, GREEN+AMBER, BLUE+AMBER, MAGENTA+AMBER, YELLOW+AMBER, CYAN+AMBER, WHITE+AMBER.  With a Dual Color configuration you don't need an LED Controller. Instead, you only need two switches (and relays); one to control each color. The primary color is chosen from the available dual color drop down list. The secondary color is always amber.